| 1 | بررسی شبیه‌سازی تأثیر زوایای کانال و انحنای مختلف بر کرنش مؤثر و نیروی فرآیند در فرآیند فشار در کانال زاویه‌دار لوله‌ای با استفاده از مقطع کانال ذوزنقه‌ای شکل | امیر اقابابایی,محمد هنرپیشه | نشریه مهندسی ساخت و تولید | 1402/08/01 |
| 2 | Experimental analysis of chip-breaker geometry effects on cutting forces, thermal load, and surface quality in turning AISI 304 stainless steel | عادل آزاد,سعید امینی,محمد هنرپیشه | Proceedings of the Institution of Mechanical Engineers, Part E: Journal of Process Mechanical Engineering | 2026-08-08 |
| 3 | Influence of ultrasonic peening treatment parameters on surface hardness, wear, and friction behavior of wire EDMed hardened Mo40 alloy steel | امیر عبدالهی,محمد هنرپیشه,سعید امینی | Proceedings of the Institution of Mechanical Engineers, Part L: Journal of Materials: Design and Applications | 2026-07-22 |
| 4 | Influence of Joint Angle on Residual Stress, Microstructural Evolution, and Mechanical Performance of Friction Stir Welded AA6061 Aluminum Alloy Using a Novel Adjustable Angled-Joint Fixture | فرزاد آقاعبدالهیان,محمد هنرپیشه | Iranian Journal of Materials Forming (IJMF) | 2026-07-18 |
| 5 | Optimization of tribocorrosion performance, wear resistance, surface integrity and residual stress of AZ31 magnesium alloy via ultrasonic shot peening | امید حقیقی ناغانی,محمد هنرپیشه | Journal of Adhesion Science and Technology | 2026-07-11 |
| 6 | The Effect of Cyclic Closed Die Forging (CCDF) Process on Fatigue Crack Growth Behavior of Precipitation-Hardened Al 7075 Alloy | محمدعلی معظم,محمد هنرپیشه | Iranian Journal of Materials Forming (IJMF) | 2026-07-10 |
| 7 | Experimental Investigation of the Thickness Distribution in a Three-Layer Aluminum-Polyethylene Sheet During Two-Point Incremental Forming Using Central Composite Design | مهدیه فرهادی,بهزاد سلطانی,محمد هنرپیشه | Iranian Journal of Materials Forming (IJMF) | 2026-04-01 |
| 8 | Effect of Incremental Forming Parameters and Annealing Condition on Principal Strain Distribution and Formability During Straight Groove Forming | امیرحسین نشاسته گیرکاشی,محمد هنرپیشه,حسین طالبی قادیکلائی | Iranian Journal of Materials Forming (IJMF) | 2026-01-01 |
| 9 | Upper-bound analysis for the combined simple shear extrusion-forward extrusion (CSSE-FE) process using a linear profile | علی ایزی,فرشید احمدی,محمد هنرپیشه | Journal of Manufacturing Processes | 2025-08-30 |
| 10 | Effect of non-equal channel angular pressing on milling-induced residual stress | محمدهادی غلامی,محمد هنرپیشه,سعید امینی | The International Journal of Advanced Manufacturing | 2025-06-16 |
| 11 | Optimization of laser bending process parameters for enhanced bending angle and residual stress control in St12 steel sheets: Experimental investigation and FEM simulation | رضا کاظمی قوهکی,پارسا انصاری,محمد هنرپیشه | Proceedings of the Institution of Mechanical Engineers, Part C: Journal of Mechanical Engineering Science | 2025-06-16 |
| 12 | Effect of shot peening and ultrasonic shot peening duration on surface integrity and electrochemical behavior of AZ31 magnesium alloy | امید حقیقی ناغانی,محمد هنرپیشه | Journal of Alloys and Compounds | 2025-05-20 |
| 13 | Experimental Investigation of Residual Stress Measurement on Cold Roll Bonded Al/Cu Composite by Incremental Hole-Drilling Method | امیرمسعود رحیمی جونوش,محمد هنرپیشه,امیر عبدالهی,مهدی محمدی مهر | Mechanics of Advanced Composite Structures | 2025-05-14 |
| 14 | Investigating the effect of die geometric parameters on the deformation behavior in the combined simple shear extrusion-forward extrusion process | علی ایزی,فرشید احمدی,محمد هنرپیشه | International Journal on Interactive Design and Manufacturing (IJIDeM) | 2025-04-30 |
| 15 | Mechanical Properties and Residual Stress Measurement in the Friction Stir Welding Process of Al 6061-T6 Plates with Copper and Brass Interlayer | سعید آریان پور کاشانی,محمد هنرپیشه | Iranian Journal of Materials Forming (IJMF) | 2025-01-03 |
| 16 | Investigation of mechanical properties and residual stress in the combined simple shear extrusion-forward extrusion (CSSE-FE) process of 1050 aluminum alloy | علی ایزی,محمد هنرپیشه,فرشید احمدی | Proceedings of the Institution of Mechanical Engineers, Part L: Journal of Materials: Design and Applications | 2025-01-02 |
| 17 | Experimental study of the effects of the ultrasonic peening treatment on residual stress, surface hardness, and hardness depth of parts cut with wire EDM | امیر عبدالهی,سعید امینی,محمد هنرپیشه | Proceedings of the Institution of Mechanical Engineers, Part L: Journal of Materials: Design and Applications | 2024-10-24 |
| 18 | Non-Uniform Simple Shear Extrusion (NUSSE) Technique as a novel sever plastic deformation technique | علی ایزی,محمد هنرپیشه,فرشید احمدی | Journal of Ultrafine Grained and Nanostructured Materials (JUFGNSM) | 2024-06-18 |
| 19 | The deformation behavior of aluminum alloy in a novel severe plastic deformation process known as combined SSE-FE process | علی ایزی,فرشید احمدی,محمد هنرپیشه | Manufacturing Letters | 2024-04-02 |
| 20 | Investigation of laser, wire-cut and plasma cutting methods on the residual stress distribution of st37 sheet using the contour method | حسین اسپنانی,محمد هنرپیشه | Iranian Journal of Materials Forming | 2024-02-07 |
